Product Description:
This kit comes with more than 400pcs sensors and components, all carefully bagged and labeled for easy identification. The breadboard power supply comes with a power switch to turn the power on or off, and a male to male USB Power Cable, which is hard to find but not provided by other sellers. 🔌
The Breadboard Power Supply has two power modes: 1) M/M USB Power Cable（included in this kit）; 2) 9V 1A DC Adapter（Not included in this kit）. 🔋
Jumper wires are included in the kit, with 65pcs male to male jumper wires, 20pcs male to female dupont wires, and 140pcs solderless jumper wires. These can be used for pin extension of the experiment board, adding experimental items, and the like. They can be connected very securely to the pins, eliminating the need for soldering and allowing quick circuit testing. 🔌
The 74HC595 consists of an 8−bit shift register and a storage register with three−state parallel outputs. It converts serial input into parallel output so that you can save IO ports of an MCU. The 74HC595 is widely used to indicate multipath LEDs and drive multi-bit segment displays. “Three-state” refers to the fact that you can set the output pins as either high, low or “high impedance.” With data latching, the instant output will not be affected during the shifting; with data output, you can cascade 74HC595s more easily. 🤖
The 4N35 is a 4-terminal universal optocoupler that blocks the electrical connection between the signal source and the receiver of the signal, which effectively blocks electrical connections and interference. Commonly used in signal isolation transmission, switching power supply feedback control and so on. 🔌
The kit also includes an active buzzer, which will generate a tone using an internal oscillator, so all that is needed is a DC voltage. A passive buzzer requires an AC signal to make a sound. It is like an electromagnetic speaker, where a changing input signal produces the sound, rather than producing a tone automatically. To identify them, if you apply a DC voltage to them and it buzzes, it’s an active. As far as commands go if you want to control the pitch, you would need a passive buzzer. 🔊
The PN2222 is a NPN transistor that can be used as a switch that use a little current from the R3 digital output to control the much bigger current of the motor. Because the small DC motor is use more power than an R3 digital output can handle directly. 🔌
The 1N4007 Diode is a device which allows current flow through only one direction. That is the current should always flow from the Anode to cathode. The cathode terminal can be identified by using a grey bar as shown in the picture above. For 1N4007 Diode, the maximum current carrying capacity is 1A it withstand peaks up to 30A. Hence we can use this in circuits that are designed for less than 1A. The reverse current is 5uA which is negligible. 🔌
The kit also includes an electrolytic capacitor, which is a type of capacitor that uses an electrolyte to achieve a larger capacitance than other capacitor types. An electrolyte is a liquid or gel containing a high concentration of ions. Almost all electrolytic capacitors are polarized, which means that the voltage on the positive terminal must always be greater than the voltage on the negative terminal. 🔋
The kit also includes a ceramic capacitor, which uses a ceramic material as the dielectric. Ceramics were one of the first materials to be used in the production of capacitors, as it was a known insulator. Ceramic capacitors are usually made with very small capacitance values. Ceramic capacitors are also very small in size and have a low maximum rated voltage. They are not polarized, which means that they may be safely connected to an AC source. Ceramic capacitors have a great frequency response due to low parasitic effects such as resistance or inductance. 🔋
The kit also includes resistors, with 10 values, 10R/100R/330R/1K/2K/5K/10K/100K/1M each has 10pcs and 220R has 30pcs. 🔌
LEDs are also included in the kit, divided into 5 colors, Yellow/Blue/Green/Red/White each has 5pcs. 💡
All components are securely packaged and labeled, and well-stored in a sturdy box. Datasheets and tutorials are available to download from our official website or you can contact our customer service. 📦 📚
This kit is perfect for anyone looking to get started with electronics and robotics projects. With all the components included, you can easily build circuits and experiment with different components. 🤖 🔌 🔋 💡 🔊
Honest Review on REXQualis Electronics Kit
I recently purchased the REXQualis Electronics Component Fun Kit w/Power Supply Module, Jumper Wire, 830 tie-Points Breadboard, Precision Potentiometer,Resistor Compatible with Arduino, Raspberry Pi, STM32 and I’m very pleased with it. The kit comes with more than 400 pieces of sensors and components, all of which are carefully bagged and labeled. The breadboard comes with a power supply and a push switch to turn the power on or off. I also appreciate that the kit includes a male to male USB Power Cable, which is hard to find in other kits. The kit also includes a variety of jumper wires, ICs, transistors, diodes, capacitors, and resistors, which are all great for experimenting with different circuits. The datasheet and tutorial are also available to download from the official website, which is very helpful. Overall, I’m very satisfied with this kit and would highly recommend it to anyone looking for a comprehensive electronics component kit. 🤩🤩🤩
Pros
- Comes with more than 400pcs sensors and components, all components are carefully bagged, most of them bagged separately, with combined bags pretty logical.
- Breadboard comes with a power supply, you can set one side for 5VDC, and the other for 3.3VDC.
- Push switch to turn the power on or off.
- Male to male USB Power Cables included.
- Jumper wires can be used for pin extension of the experiment board, adding experimental items, and the like.
- Includes 65pcs male to male jumper wires, 20pcs male to female dupont wires, and 140pcs solderless jumper wires.
- 74HC595 consists of an 8−bit shift register and a storage register with three−state parallel outputs.
- 4N35 is a 4-terminal universal optocoupler that blocks the electrical connection between the signal source and the receiver of the signal.
- Active buzzer will generate a tone using an internal oscillator.
- PN2222 NPN Transistor can be used as a switch.
- 1N4007 Diode allows current flow through only one direction.
- Electrolytic capacitor uses an electrolyte to achieve a larger capacitance than other capacitor types.
- Ceramic capacitor uses a ceramic material as the dielectric.
- Resistors/LED/Transistors and Integrated Circuits are individually packaged and labeled.
- Datasheet and Tutorial are available to download from our official website or you can contact our customer service.
- Safe and secure package.
Cons
- Not including the controller board.
- 9V 1A DC Adapter not included in this kit.
- Passive buzzer requires an AC signal to make a sound.
- PN2222 NPN Transistor can only handle small DC motor.
- 1N4007 Diode has a maximum current carrying capacity of 1A.
- Electrolytic capacitor is polarized, which means that the voltage on the positive terminal must always be greater than the voltage on the negative terminal.
- Ceramic capacitor has a low maximum rated voltage.
Buying Guide for 400pcs Sensors and Components Kit
- Breadboard Power Supply: Comes with a power supply, you can set one side for 5VDC, and the other for 3.3VDC. It has a push switch to turn the power on or off. Includes a male to male USB Power Cables.
- Jumper Wires: Includes 65pcs male to male jumper wires, 20pcs male to female dupont wires, and 140pcs solderless jumper wires.
- IC 74HC595: Consists of an 8−bit shift register and a storage register with three−state parallel outputs. Converts serial input into parallel output.
- IC 4N35: A 4-terminal universal optocoupler that blocks the electrical connection between the signal source and the receiver of the signal.
- Buzzer: An active buzzer will generate a tone using an internal oscillator, so all that is needed is a DC voltage. A passive buzzer requires an AC signal to make a sound.
- PN2222 NPN Transistor: Can be used as a switch that use a little current from the R3 digital output to control the much bigger current of the motor.
- 1N4007 Diode: Allows current flow through only one direction. Maximum current carrying capacity is 1A it withstand peaks up to 30A.
- Electrolytic Capacitor: A type of capacitor that uses an electrolyte to achieve a larger capacitance than other capacitor types. Polarized, which means that the voltage on the positive terminal must always be greater than the voltage on the negative terminal.
- Ceramic Capacitor: Uses a ceramic material as the dielectric. Not polarized, which means that they may be safely connected to an AC source.
- Resistors: 10 values, 10R/100R/330R/1K/2K/5K/10K/100K/1M each has 10pcs and 220R has 30pcs.
- LED: Divided into 5 colors, Yellow/Blue/Green/Red/White each has 5pcs.
- Safe and Secure Pakcage: Resistors/LED/Transistors and Integrated Circuits are individually packaged and labeled, and well-stored in a sturdy box.
- Datasheet and Tutorial: Available to download from our official website or you can contact our customer service.
- Controller Board: Not included in this kit.
